USB wifi适配器问题

我有一个USB wifi适配器（Edimax EW-7612UAn V2），其驱动程序安装在我的鹦鹉系统上，并且我的计算机的pci与鹦鹉不兼容。问题是鹦鹉说当我使用普通wifi和当我使用airmon时，两个适配器都被禁用了-ng usb wifi适配器工作正常，并且计算机的pci当然不能工作。当将我的pci放在显示器中并且将我的USB wifi适配器置于受管模式时，尽管usb适配器不在监视模式下，网络管理器也会从wifi菜单中将它们都删除。

换句话说，如果主pci不兼容或无法识别，鹦鹉将无法识别这两种适配器。所以，我该怎么办才能迫使鹦鹉只使用USB WiFi适配器？

lsusb -v结果：

Bus 002 Device 003: ID 7392:7822 Edimax Technology Co., Ltd 802.11n WLAN Adapter
Couldn't open device, some information will be missing
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0        64
  idVendor           0x7392 Edimax Technology Co., Ltd
  idProduct          0x7822 
  bcdDevice            2.00
  iManufacturer           1 
  iProduct                2 
  iSerial                 3 
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength       0x002e
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0x80
      (Bus Powered)
    MaxPower              500mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           4
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol    255 Vendor Specific Protocol
      iInterface              0 
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x03  EP 3 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x84  EP 4 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               1

网络管理员的屏幕截图

rf-kill的结果：

0: hp-wifi: Wireless LAN
    Soft blocked: no
    Hard blocked: yes
1: hp-bluetooth: Bluetooth
    Soft blocked: no
    Hard blocked: yes
2: phy0: Wireless LAN
    Soft blocked: no
    Hard blocked: no
3: phy1: Wireless LAN
    Soft blocked: no
    Hard blocked: yes

ifconfig的结果：

eth0: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        ether 34:64:a9:73:43:20  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 1000  (Local Loopback)
        RX packets 8  bytes 396 (396.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 8  bytes 396 (396.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0